| |
CONTACT
US |
| |
Welcome to Yuehua Sanitary Ware Co.,Ltd., If you
have any interest on our products or any comments for us, please
send us a email: |
| |
Export Dept11
Tel:+86-757-88222272
Fax:+86-757-88222272
E-mail:china-fspa@vip.163.com
Contact Person:Paris To
Export Dept12
Tel:+86-757-88213118
Fax:+86-757-88213118
E-mail:fspa@vip.163.com
Contact Person:Jacky Fung
Export Dept11
Tel:+86-757-88222272
Fax:+86-757-88222272
E-mail:china-fspa@vip.163.com
Contact Person:Paris To
Export Dept12
Tel:+86-757-88213118
Fax:+86-757-88213118
E-mail:fspa@vip.163.com
Contact Person:Jacky Fung
|
|
|
|
Massage Bathtub :
Breakdown phenomenon and settlement: |
| Phenomenon |
Reasons |
Maintenance |
| No power or electricity leaking protection device is activated |
1. Electricity leaking protection device cut off
power source when electricity line is not well
connected.
2. Power or electricity circuit have phenomenon
of electricity leaking. |
1. check and reconnect the wiring system.
2. check the power source, electricity
circuit and ground line. |
Water Jets are
not working. |
1. check the system whether is on.
2. the impeller of water pump doesn't rotate.
3. water pump is broken which caused by
working without water coming in. |
1. turn on the system.
2. check through and remove the garbage
which is inside the pump. Switch pipe
can be removed.
3.install a new water pump |
The intensity of
hydro-massage
cannot be adjusted |
1. water pump's suction has not enough power.
2. air adjustment valve is abnormal.
3. jets or nozzles are blocked. |
1. check the water pump whether is working normally
2. change the air adjustment valve.
3. remove things which are blocking the jets. |
Water leaks from
the pipes
|
1. seal ring is broken.
2. screws doesn't lock tightly.
3. pipes doesn't seal properly. |
1. chang seal ring.
2. lock the screws tightly.
3. re-seal the silicone.
4. change water pipe |
Jets shower can
not be work. |
1. voltage is abnormal
2. Switch cannot be work
3. control panel cannot be work.
3. water in electromagnetism valve is be blocked |
1. please use it at the normal situation of voltage.
2. check and change the switch.
3. maintain and change the control panel.
4. get rid of mess of the jets. |
| No lighting |
1. The bulb is broken.
2. power line is disconnected.
3. control panel is broken. |
1. change a new bulb..
2. re-connect the circuit..
3. maintain or change control panel |
| Cleaning and Maintenance: |
1. The daily maintenance should be cleaned with
ordinary detergent and soft cloth. Please do not use the detergent
which contains acetone or ammonia liquid. If there marks or
something like glue on the surface of bathtub, just polish
it with soft cloth dipping with gas.
2. If there are scratches on bathtub surface, please polish
it with 1500# frosted paper dipping with liquid and burnish
it with toothpaste. It will be shining again after that.
3. If there are furring on the surface of bathtub, it can
be take away by mild acid detergent, for example wipe the
bathtub with lemon juice or vinegar which be heated.
4. Do not wipe the chrome plated spare parts all the time,
and do not get in touch with chemical detergent etc. Otherwise
the surface of chrome plated will be destroyed. The product
should be clean by soft cloth other than coarse cloth.
5. To check the water pipe regularly in order to avoid troubles
from crack of water pipes or blocked inside.
6. If there are something such as hair stuck inside the jets,
then just to twist out the jets and remove it.
7. To clean hydro-massage equipment: To full fill hot water
which is 40'C, and pour 2g/L detergent, start hydro-massage
function more than 5 minutes, then turn off the massage function
and drain out the water. Next, to full fill cold water and
start hydro-massage function for 3 minutes, then turn off
the massage function and drain out the water, at last, to
dry the bathtub with towel.
8. Filter should be clean once a week.
9. Keep out from combustibles and goods which over 80°C to
avoid fire disaster and damage the product.
10. The bathtub should be transported carefully. Do not lay
heavy things on it and do not bump and shaking the tub. If
the bathtub has not been used for a long time, drain out the
water of the bathtub and keep it in a dry and ventilate environment.
Avoid corrosive gas. |
|
NO :1 2
|
